• Voltage Rating: 277/480 VAC @ 60 Hz
• Current Rating: 5 through 150 amperes
• HEMP Compliance: Per MIL-STD-188-125-1 and MIL-STD-188-125-2 as Power Line (Intrasite) point of entry filter for short (E1) and intermediate (E2) pulses.
• Insertion Loss: Standard performance (curve 1) per MIL-STD-220
• Leakage Current: < 10% of rated current 10 through 150 amperes, < 1 amp for 5 amp filters
• Insulation Resistance: Per MIL-PRF-15733, prior to discharge resistor installation.
• Dielectric Withstanding Voltage: 2250 VDC line-to-chassis per MIL-STD-202, Method 301 prior to surge arrestor and discharge resistor installation
• Voltage Drop: Less than 1% of rated voltage per paragraph 4.6.8 of MIL-PRF-15733
• Voltage Discharge: Discharge to less than 30 Volts within 30 s after removal of power
• Operating Temperature: -40 ºC to +65 ºC
• Storage Temperature: -55 ºC to +105 ºC

• Voltage Rating: 277/480 VAC @ 60 Hz
• Current Rating: 5 through 150 amperes
• HEMP Compliance: Per MIL-STD-188-125-1 and MIL-STD-188-125-2 as Power Line (Intrasite) point of entry filter for short (E1) and intermediate (E2) pulses.
• Insertion Loss: high performance (curve 2) per MIL-STD-220
• Leakage Current: < 10% of rated current 10 through 150 amperes, <1 amp for 5 amp filters
• Insulation Resistance: Per MIL-PRF-15733, prior to discharge resistor installation.
• Dielectric Withstanding Voltage: 2250 VDC line-to-chassis per MIL-STD-202, Method 301 prior to surge arrestor and discharge resistor installation
• Voltage Drop: Less than 1% of rated voltage per paragraph 4.6.8 of MIL-PRF-15733
• Voltage Discharge: Discharge to less than 30 Volts within 30 s after removal of power
• Operating Temperature: -40 ºC to +65 ºC
• Storage Temperature: -55 ºC to +105 ºC

• Voltage : 0 to 480 Volts
• Current : 0 to 100 Amps
• Frequency : DC to 400 Hz
• Insertion Loss : 100 dB minimum from 14 kHz to 10 GHz
• Operating Temperature : -40 ºC to +71 ºC
• Storage Temperature : -55 ºC to +105 ºC
• Altitude : Maximum of 15,000 feet
• Humidity : 10 to 90 Percent
• Fungus : Non-nutritive materials are used
• Corrosion : Hermetically sealed steel or aluminum enclosures with tin-lead plating

• Voltage Rating : 48 VDC or 120 VAC @ 0-60 Hz
• Visual/Mechanical : Per MIL-PRF-15733, paragraph 4.6.1
• Capacitance : Per MIL-STD-202, Method 305 @ 1 kHz
• Insulation Resistance : Per MIL-PRF-15733, paragraph 4.6.7 with Hemp Protection Module removed.
• Dielectric Withstanding Voltage : Per MIL-PRF-15733, paragraph 4.6.5 with Hemp Protection Module removed.
• Standard Insertion Loss : Per MIL-STD-220, 20 dB @ 10 kHz, 80 dB @ 10 MHz to 10 GHz
• Terminal Strength : Per MIL-PRF-15733, paragraph 4.6.11
• Voltage Discharge : Discharge to less than 30 Volts within 2 seconds after removal of power
• Terminals : 1/4" Quick Connect Tab
• Operating Temperature : -55 ºC to +71 ºC
• Storage Temperature : -55 ºC to +105 ºC
• Chassis & Terminal Finish : Electro Tin-Lead
• Chassis Material : 20 GA. Cold Rolled Steel

• Voltage Rating : 48 VDC or 120 VAC @ 0-60 Hz
• Visual/Mechanical : Per MIL-PRF-15733, paragraph 4.6.1
• Capacitance : Per MIL-STD-202, Method 305 @ 1 kHz
• Insulation Resistance : Per MIL-PRF-15733, paragraph 4.6.7 with HEMP Protection Module removed.
• Dielectric Withstanding Voltage : Per MIL-PRF-15733, paragraph 4.6.5 with HEMP Protection Module removed.
• High Performance Insertion Loss: Per MIL-STD-220, 100 dB @ 14 kHz - 10 GHz
• Terminal Strength : Per MIL-PRF-15733, paragraph 4.6.11
• Voltage Discharge : Discharge to less than 30 Volts within 2 seconds after removal of power
• Terminals : 1/4" Quick Connect Tab
• Operating Temperature : -55 ºC to +71 ºC
• Storage Temperature : -55 ºC to +105 ºC
• Chassis & Terminal Finish : Electro Tin-Lead
• Chassis Material : 20 GA. Cold Rolled Steel

Signal Line NEMA Cabinets